Conjoined Twins Car Seat

We were approached by Erin Herrin in 2002 and were asked if we could help to build a car seat for her conjoined twins. Kendra and Maliyah shared a set of legs and some organs, but, were two separate beautiful children from the waist up. One day driving home from a doctor's appointment, Erin was pulled over and the Policeman gave her a lecture about how she can't put two babies in one car seat. She explained the circumstances to the police officer and this started the idea of how to place conjoined twins securely and safely in a car seat. After many different ideas on how to modify the car seat and doing as little as possible to the integrity and original design from the manufacturer, we decided to cut the seat down the middle in the back and place an adjustable piece of plastic behind the backrest to secure it. This allowed for the seat to be opened up wider as the girls grew and needed more room to fit into the car seat. I learned early on to "Make It Adjustable or Make it Again".... This has become our main thought as we create anything at UCAT. We also added some straps and buckles to make it as safe as possible in case they were in an accident. In the end, I feel that we didn't weaken the car seat too much from what the manufacturer had designed it for and I am sure they would disagree. Unfortunately, we did not take any pictures of the car seat or the girls strapped into the car seat. There is one picture of them after their separation as they had outgrown the seat and this picture is available on their website.

Early this year we were contacted by another family from Arizona asking if we could create a car seat for their conjoined twins Emma and Taylor. As UCAT only works with citizens of Utah we ran this project through a group of volunteers from the Utah chapter of the TETRA Society of North America. this is a group of Engineers that volunteer their talents and time to figure out solutions for assistive technology for individuals in the western states. These twins are joined at the sternum and required a car seat in which they could lay down. They do not have the head strength to sit up so the family asked for a carseat that would lay them down. After a couple of prototypes using a couple of different materials, we decided to use 1/4-inch ABS plastic. We work alot with this plastic because it can be heated and shaped. In the long run, it was actually a very simple design that was a flat surface with sides to keep the girls safe and comfortable. We then added straps that would attach over the shoulders, around their torso and around their hips. The family tells me that the seat has worked out very well and that there were only slight adjustments that they needed to make. Once the girls are stronger and able to sit up better, we hope to make them a car seat that will allow them to sit up.

TETRA wrote a story in their summer edition of their Gizmo Newsletter.

Adapted Crib

One of our clients with cerebral palsy contacted us telling us that she was pregnant and was wondering if we could help her with some things. The first thing she needed was a crib that would allow her access to putting her child in and out through the front. She spent much of her time on her knees to get around the house scooting on a little platform with wheels. There are accessible cribs on the market but they cost around $1,500.00. We were able to get a crib donated by the Director of UCAT and to modify it accordingly. For our adaptation of this crib, we prevented the front gate from being lowered as designed and added reinforcement to the top portion of the front gate. We also had to lower the mattress.

We then cut the gate in half allowing it to swing open on the left side. The right side was secured.

In order for the crib to latch securely, we purchased a child protective latch that would normally be installed inside a cabinet to keep children out of the cabinet. In our situation, we wanted to keep the child inside. We chose this style of latch because the mother did not have good grasp in her hands and could not manipulate small latches or hooks. She was able to pick up the magnet and to put it on the latch which would release it allowing her to open the gate and to remove her baby from the crib.

Environmental Controls

One thing that UCAT has come to specilaize in are environmental controls. Environmental controls allow individuals with a variety of abilities to do exactly that...to control their environment. From something as simple as controlling a television with a button, sip and puff, or by voice to controlling lights, heats, air conditioning, dvd players, telephones, door openers, fans, appliances, and almost anything that can be imagined. We have a great demonstration board that we set up and take around to show groups what is available. It is one of the true joys of my job in giving individuals the abiltity to control their environment. To give someone the ability to simply change the channel on their television is a huge feeling of independence for some so they can watch what they want and not have to ask a family member or attendant to do it for them. We typically use X-10 controls to give individuals control of lights and appliances. With a palm pad and some modules, I often go into a home and within half an hour and less than $100.00 we can give someone the ability to turn on a couple lights throught their house and a fan or heater.

Helmet for Self-Injurious Behavior

We were contacted by a Group Home that had a 30-year-old man with severe mental disabilities which had some self-injurious consequences. A couple times per week, he would get upset and he would start slamming his head into the ground usually ending up in a bloody face or stitches. Typically, the staff would jump on top of him and try to restrain him from harming himself which would only agitate him more and made it difficult for him to stop.

Through some brainstorming we came up with an idea of a helmet that would protect him from harming himself when he does experience this behavior. We needed to create something that would allow him total protection of his face while allowing the staff to easily put this on him during his fits of rage.

We chose to purchase a street motorbike helmet and to modify it.

First, we cut the helmet up the side and attached a hinge at the top that would allow the helmet to open up wide enough to get it over his head easily.

Next, we added buckles onto the side that allowed the helmet to latch shut when the helmet was closed.

Staff would get onto his back while he was headbanging and could put the front of the helmet over his face and then shut the back portion of the helmet to close it. We installed some ABS plastic over the face shield for added protection and also to create a dark environment for him that would help to calm him down to stop the headbanging. Instead of three or four staff members jumping on him to restrain him (and possibly at risk of injury themselves) one person was able to get this onto his head very quickly and then let him bang until he settled down. The combination of the darkness and that he was not causing pain to himself, greatly shortened the amount of time that he continued his behavior and almost completely eliminated any injury to himself.

Electric Train Controller

A local pastor in the area builds electric train sets for children who he feels could benefit from the joy of playing with the trains. He contacted us asking if we could design a way for a boy with only head movement to control the train. One of my good friends, Mel Torrie, is owner of an amazing company that builds autonomous vehicles and robotic devices. Autonomous Solutions has some engineers that volunteer their time to create projects using their electrical and engineering skills. they have put together a local chapter of volunteers under the Tetra Society and they complete projects in Utah and the Intermountain West.

To allow control of the train, they created a voltage regulated box that was controlled by sipping and puffing into a tube. One puff would move the train forward with a range of 10 puffs to control the desired speed. A sip in the tube would slow the train down and/or put the train in reverse. Tetra put a story about it in their publication, the GIZMO.

Horizontal Work Station

A 31-year-old female who is quadriplegic and experiences severely low blood pressure is required to remain in a prone position 95% of the time. Sitting up slightly or rolling over often caused her to blackout as a result of her low blood pressure. She spent most of her time in bed as a result of this. Our goal was to provide her the highest potential for productivity that included means of accommodating her need to be lying prone for long periods, and, to perform functional tasks in this position.

To accomplish this goal, we created a short table that she could lay upon in the prone position to accomplish a number of tasks mainly working on a laptop, reading and writing. We made the frame from unistrut approximately 16-inches tall. upon that we created a padded base that had two areas cut out to allow her arms to lower through. We also purchased a massage table head support which she would rest her head upon and could see down to the work area below. This head support allowed for different positioning for the most comfortable postion, allowing her to work in this position for up to 6-hours at a time.